Gutterglove Stainless Steel Gutter Guards are relatively easy for a homeowner to install. I have almost 300 ft of gutter to cover. I ordered the incorrect width 6-7” when I should have ordered 5” but i have figured a way to install the pieces and not have to trim the width. I have a scaffold which helps by not having to stand on a ladder and reach out. I use an 18v screw gun to drill in the self-tapping screws. The hardest thing i have to do is cut the length with a hacksaw. Once installed they look great. Haven’t had any moisture to test them so far. Leaves are starting to fall and Winter will be here soon and they wil get plenty of workout.

Easy install, very sturdy. I installed these and another type a couple of years ago and these out-performed the other type significantly, so I decided to install the rest with these. I do recommend the bigger size even if you have smaller gutters.

Easy to install. The provided self thread screws made project easy. Recommended tools are screw drivers (cordless) tin snips. I also needed hack saw for tight cuts in a few areas. Many leaves have fallen and works great!

I installed 120 ft of the Gutter Glove in about 2 1/2 hours. We have had 3 good hard rains since and results are super. I may need to install a valley diverter to help direct the valley water. Otherwise this is best product yet. They replaced LEAFGUARD GUTTERS!

The product comes in 48" lengths. Although that is true, the extruded aluminum at the front and back edges is held short by about 3/4" from each end of the mesh. The mesh is 48" long. By the time you bend the mesh at each end to abut the adjacent section, you end up with around 47" of coverage at a straight run. If you are at the end of the gutter and want closed ends to keep critters and such from getting under the guard, there is at least another 3" of length lost to bend at each end. The point is to make sure you over estimate your lengths to make sure you have enough to finish the job. I needed about 112' so I ordered a 96' and 24' package to complete my house but ended up short by about 10' and I had very little waste. Otherwise, this seems like a descent product and the installation was about what I expected. It is too early to tell since I just installed them a couple weeks ago and the leaves won't start falling for a few weeks, but I feel pretty confident I won't be climbing any ladders to clean out my gutters for a while. We have had a good downpour and I saw no issues of water running over the top of the gutters.

We bought this a month ago. Instructions were excellent. The stainless steel gutter is a great product. The only negative: the self taping screws were too short for the back of the gutter. In the front they're sufficient, but with the gutter being bent to fit in the back, they are too short. We went to a hardware store and bought longer self-tapping screws and that worked so much better. The look is superior to anything else we've tried.

Great quality & material. Biggest gripe is w/ roof pitch >6. After bending especially when it is necessary in the direction into gutter. The back thinner width extrusion w/ the small lip doesn’t provide 1/4” nut driver tool clearance for driving screw nor screw head clearance , screw head sits on top of lip & it’s short length does not provide enough screw thread engagement into fascia board. Also, not enough screws for (6) screws per section for this type of installation.

If your roof pitch is less than 6, this might be a good product. If your roof is more than a 6 pitch, the devices have to be bent/modified for the excessive pitch. It was not worth my time to bend. If I had a brake, I maybe would have tried.

The packaging is unacceptable. This is delivered from the manufacturer and will 100% be damaged when you get them from Fedex.

Purchased in the summer and installed them on my gutters of a 1300 sq. foot home and also on a 2 car garage. The stainless steel guards are excellent quality. However, when they were put to the test of a michigan winter, they failed. First lets start at why I purchased these. I live next door to property that has alot of trees, including 1 very large pine tree. (I have no trees on my property). I wanted gutter guards that not only keep leaves and other debris out, but I really wanted them to keep the pine needles out of my gutters. In the fall, I noticed that the pine needles stick in the tiny holes of the gutter guards. Sounds great right.....WRONG! My house looks like it needs a haircut from all the pine needles sticking up. I tried to blow them out of the stainless mesh with a ladder and a leaf blower. They wouldn't budge. They I tried the hose(on the ladder, directly spraying water on them, no luck!) Then I thought, what about a brush on a handle, like the one they advertise on their video. NOPE! So the problem is that while they do keep EVERYTHING out of your actual gutters, keep in mind that because there are so many pine needles filling the holes in the gutter guards, it is difficult for the water to penetrate into the actual gutter and make its way AWAY from your home. The water runs over the gutters and is now producing icicles terribly around my entire home and garage. (We just had our first big snow fall of the year) Great product, nothing gets in the gutters, however, I can see me having to paint my white gutters this summer and possibly removing them due to fact that all these icicles, coupled with the fact that not all the water can actually make it through these tiny holes contradicts why I bought them in the first place. By the way, during heavy rains, the water has difficulty penetrating the holes in the gutter guards and runs over...so you will eventually have water streaks.