It is a beautiful piece of furniture and was easy to put in according to the Plumber so I look forward to many good years with this vanity !

Love this vanity! Such great quality. Feels really solid and sturdy compared to others I looked at. The natural oak is a beautiful colour. I switched out the hardware to matte black and it really pops. My only complaint is that the original hardware broke when I tried to remove it, luckily I was already planning to switch it.

The appearance and functionality of the vanity is great. However, the installation process was harder than anticipated. The board that braces the back of the vanity interfered with the drain hole in the wall, so I had to notch out a "half moon" section of the top of the board to make it fit against the wall. Then when trying to reinsert the shelf, the back of the shelf interfered with the water supply lines. I had to cut 1 inch off the back of the shelf to make it fit. Otherwise, we love the outcome.

I bought this vanity as it was the right height and design for a vessel top BUT the standard top that came with the unit was EPOXIED to the unit and integral to its structure so I had to use "as is". This should have been disclosed as most vanities come with the top unattached so that installation is easier.(i.e. attaching it to the wall). The design is very good as the top shelf comes with a cutout for the waste pipe in center. If your waste is at an angle (left or right) the shelf might not be useable. The primary reasons we bought this particular unit was the right color in the right size for small master bath en suite.

I wish that workers would take the time to sample items before packing them. The right door on the vanity after adjusting the hinges any way you could would still not close all the way. You have to lift the door up to close. I would otherwise give a 5 star because it does look nice. Please workers do your dam job!!!

I really liked this model. Very tasteful, neutral and turned my old bathroom from "i want to remodel this today" to I "i am so happy I found Ove Kansas" as it saved me thousands of dollars from a full remodel. I upgraded all fixtures around it, repainted and used new decor. Priceless fix!

We got to refresh a half bath. It looks good but is a bit wobbly/flimsy by itself. We secured to the wall using some screws into studs and it’s perfectly solid now. Top/basin is great, and color matched what we were going for on decor. Doors and drawer will require a little adjustment to fit perfectly, which is to be expected. One caution for those in older houses and vanities with drawers in the bottom. Our house is from the 70s so plumbing connections / drain are quite a bit lower than modern standards with this height vanity. Our install required clearancing the drawer back, a cutout in the lower shelf and a cutout in back support to clear drain / trap. This isn’t surprising, we had to do with another Ove vanity at our old house due to same issue, but didn’t learn out lesson!

The vanity was shipped quickly, and was packaged well, but sadly arrived with a little bit of damage. It wasn't very noticeable though so I was able to get a discount and keep it. It looks good, but it is made of very cheap wood/partial board. The laminate one of the legs started to come off simply by sliding it across the floor during install. The bottom shelf was too high for my existing P-trap, a common issue I read in the reviews. So we had to cut out the bottom shelf and the back of the drawer. This required removing the back stretcher that went across the back which made the vanity much less sturdy. That said, it does have soft close hinges, and nice hardware, and the sink seems to be good quality, plus it comes with a matching backsplash, which is nice. Overall, for the price, it is a good vanity that looks nice, but it is not the most well built or sturdy vanity on the market.

We were really looking forward to our vanity coming in, and at first glance it is very beautiful. Sadly, the counter top was damaged and has a chip in it, and one of the legs seems to be peeling as well. Will be reaching out in hopes of being sent another top, as receiving a damaged one is just poor service.

We installed it 2 weeks ago. As noted ,the vanity to is epoxied to the unit.While unusual, we were able to install it anyway.The shelving under the sink needed to be cut away on our unit also to fit the pipes under it.I think that it would be a design improvement to pre perforate this shelve to break away,or slide out, maybe both. While we were able to get around this, a tiny water leak under the sink that developed because of difficulty reaching up behind the pocelain to tighten the bolts started causing the particle board in the back under the sink to break apart and cause stripping of the thin veneer on the back leg.When I purchased this unit online it looked like wood, the particle board constitution wasnt mentioned, and I would not have spent the considerable amount for that because I know it can't get wet.I purchased another unit last year for half of the cost of this one that is entirely hardwood.Since it is a bathroom vanity (!),it is inevitable for this construction to deteriorate over time.Also, we needed to install pvc flex pipe to manuever in the plumbing, which ultimately will impact any future home inspection. Added to all the above, the backsplash has to be epoxied to the sink!( No tools or predrilled holes to do this) All the above may require that we uninstall tbe whole thing and return it.Too bad, it was alot of work,and I really liked the design.