I ordered a second batch - they are that good. Far superior to the plastic large-grid covers I had on my gutters before. In an area with many large trees, these are the answer, especially if you don't want to replace entire guttering system. Highly recommend!

These gutter covers work very well. I installed two days ago, and have gone through our first rain since the install with great results. There is no doubt that these will keep the debris (including roofing sand) out your gutters. I was somewhat concerned whether the water would actually still be able to get into the gutters. After the first rain, all went well. We got about an inch of rain in 24 hours, and the gutter covers took it well. Will have to wait and see how a real downpour goes. The installation was OK. Straight runs go very well, but inside and outside corners were tough to install. The instructions for installation are outstanding! The gutters covers were tough to cut. Good thing - they seem very durable, making them tough to cut; bad thing - they are tough to cut. Take the good with the bad. The use of tin snips to cut these is pretty tough. I used a dremel with a metal cutoff wheel, and that went somewhat better. Overall - A+ for quality, A- for installation ease, A + for quality of the supplied installation instructions.

Very easy install, quality self tapping screws along with the guards 4.5 stars. The hardest part about the install is moving the ladder and climbing. My pole barn is 24 by 32 with a 24 ft lean to. Perfect one piece left over. Have the same guards on my house but had them installed by contractor.

This went much better than I thought. They are made well and easy to attach to my existing gutters. The hardest part was getting up on the ladder, but the best part is I’ll never have to do that again! Can’t wait to see how well they do in the coming fall season.

Just had this installed today after fighting with years of clogged gutters. Looks like it will definitely do the job. Very sturdy and will never rust. Mesh is tight enough that nothing but rain water could get through. Looking forward to years of not cleaning gutters again. Installs easy

I Installed these on my home by myself in 4 hours and it rained almost immediately after I finished. They work well except at the inside corner (valley) of roof. I ordered the recommended rain diverter and hopefully this will take care of the problem. A little disappointed in the shipping cost of $10 for a $13 diverter though

Easy to install, although our gutter required option 4, which was a bit more work...but at least there are instructions to cover all types! Very sturdy stainless mesh, and appears that it will last for a long time. Great that screws are included, also. No trips to the hardware store!

I recently installed these gutter guards. Following the videos, installation was remarkably easy and fast! The construction of these guards is comparable to, or better than, any you'll find in the market. The fit is excellent, and I'm positive that I won't be cleaning leaves out of my gutters this fall. My only issue was in having difficulty removing the backing from the tape. I definitely recommend these to all.

As advertised, This product was easy to install. I opted to use the included screws and the included nut driver. I installed almost 70 feet in about 4 hours. It was easier than I thought. Once I figured out the motion needed to slip it under the existing shingles it went on fast. Had to clean by gutters twice in 6 months before this product. I can already see the leaves blowing off the gutters.

I recently bought and installed this stainless system for my upstate NY ranch style home. Pine needles have been my biggest challenge and I tried the inexpensive plastic home center covers which did ok until the glued on screening tore away. These gutter covers looked to be just the ticket if I could install them myself. Earlier this week, I installed them on a 30 foot section which included an inside corner. I had to bend the back of each panel downward for the best looking result. After trying the method that came with the instructions, I decided to make a simple homemade brake. I screwed two 4 foot, one by two inch boards, to a piece of plywood just far enough apart to slip in a section of gutter guard and bent each piece with ease. At 72, my hands have lost much strength, this made the bending effortless. I also used a small angle grinder with a metal cutting disc to make any cuts needed. This also proved easier than tin snips for me. Once I got going, it took me about 3 hours to complete the section and I can’t wait for another decent day to finish the job. We had a medium shower this morning and they drained perfectly. I am waiting for a deluge to see if there is any overflow like I had with my plastic guards. One more thing I will mention. It appeared that I was using the fasteners provided at a rate where they would not finish the job. I emailed the company and more are on the way, no charge. My gutter cleaning days are over! A great product!